Android java & MCU Keil/uVision, STM32F

링크: http://cskimair.tistory.com/entry/Mango64-linux-qt-porting-03rootfs

링크: http://cskimair.tistory.com/entry/Mango64-linux-qt-porting
*. 아래 내용은 "MangoStory 5-안드로이드 시스템 프로그래밍 완전정복"를 기본으로 작성된 내용입니다.
- 개발환경 설정 및 커널 빌드등의 환경설정방법을 참고한 것입니다. 

가능하면 책내용과 유사하도록 하고 책에서는 ubuntu9버젼이 기준이나
Ubuntu9버젼은 지원이 종료되면서 Ubuntu10.04에서 업데이트 되면서
이문서 역시 우분투10.04버젼에서 돌아가는 것을 기준으로 하였습니다.

0.tftp_nfs_etc  설정

- 아래와 같은 디렉토리에 uboot prompt 에서 print한 내용을 파일로 저장해놨습니다.

kra@ubuntu:~$ cd 00.tftp_nfs_etc kra@ubuntu:~/00.tftp_nfs_etc$ cat uboot-mango64-prompt_serial-console.txt

보드(스마트박스)를 부팅하면 아래와 같은 화면이 나옵니다. 이때 시리얼 콘솔화면에서 키보드를 치면
프롬프트(MANGO64#)가 나옵니다.

U-Boot 1.3.4 (Sep 19 2011 - 01:21:21) for MANGO64 uboot-1.3.4-pooh11 CPU:     S3C6410@532MHz          Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode) Board:   MANGO64 DRAM:    128 MB Flash:   0 kB NAND:    256 MB In:      serial Out:     serial Err:     serial Hit any key to stop autoboot:  3

print 명령을 입력하면 아래와 같은 내용이 출력됩니다.
아래에서 bootcmd 가 중요하나 초기 설정후 변경할일이 없습니다.
bootargs가 nfs로 부팅하거나 nand로 부팅할때 설정을 바꾸면서 사용하게 됩니다.
bootargs_nfs , bootargs_nand 등의 파라메터는 정보를 임시 저장하기 위한 파라메터입니다.

MANGO64 # print mtdpart=40000 400000 4000000 bootdelay=3 baudrate=115200 ethaddr=00:40:5c:26:0a:5b bootcmd=nand read 50008000  40000 300000; bootm 50008000 bootargs_nand=root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200 bootargs_android_nfs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/mango64_android,nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0:off mem=128M init=/init console=ttySAC1,115200 bootargs_nfs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/RootFS-NEW2    ,nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0:off mem=128M console=ttySAC1,115200 bootargs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/RootFS-NEW2, nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0:off mem=128M console=ttySAC1,115200 filesize=2FD9C4 fileaddr=51000000 gatewayip=192.168.11.1 netmask=255.255.255.0 ipaddr=192.168.11.110 serverip=192.168.11.131 stdin=serial stdout=serial stderr=serial Environment size: 981/16380 bytes MANGO64 #

환경변수의 변경방법은 아래와 같습니다. ""사이에는 한줄입니다.

MANGO64 # setenv bootargs "root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/RootFS-NEW2 ,nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0:off mem=128M console=ttySAC1,115200"

디렉토리의 구성은 아래와 같이 00~09로 심볼릭 링크를 걸어놓았습니다.

kra@ubuntu:~$ ls -al total 276 drwxr-xr-x 46 yhoh   yhoh  4096 2012-01-30 21:09 . drwxr-xr-x  4 root   root  4096 2012-01-29 15:04 .. lrwxrwxrwx  1 yhoh   yhoh    28 2012-01-30 13:44 00.tftp_nfs_etc -> mango-developing-environment lrwxrwxrwx  1 yhoh   yhoh    25 2012-02-01 23:32 01.uboot -> mango64-u-boot-2010-0816/ lrwxrwxrwx  1 yhoh   yhoh    26 2012-01-29 23:52 02.kernel -> mango64_kernel_2010_07_02/ lrwxrwxrwx  1 yhoh   yhoh    33 2012-01-29 23:52 03.rootfs -> dhkim1027-mango64_rootfs-6501333/ lrwxrwxrwx  1 yhoh   yhoh     5 2012-01-29 23:53 04.tslib -> tslib lrwxrwxrwx  1 yhoh   yhoh    38 2012-01-30 00:13 05.qt4.7 -> qt-everywhere-opensource-src-4.7.0-rc1 lrwxrwxrwx  1 yhoh   yhoh    18 2012-01-30 20:49 06.sound -> alsa-sound.1.0.15/ lrwxrwxrwx  1 yhoh   yhoh     8 2012-01-30 20:18 07.mango64-test -> m64led8/

1. uboot 컴파일
- uboot 디렉토리로 이동합니다. 

kra@ubuntu:~$ cd 01.uboot kra@ubuntu:~/01.uboot$ make clobber  kra@ubuntu:~/01.uboot$ make smdk6410_config Configuring for smdk6410 board...  kra@ubuntu:~/01.uboot$ make

*. 참조 URL: http://cafe.naver.com/embeddedcrazyboys/5256  , http://cafe.naver.com/embeddedcrazyboys/3220 

1.1 u-boot.bin 보드로 다운로드 
위에서 생성된 ~/01.uboot/u-boot.bin 파일을 이용해서 윈도우 환경에서 스마트박스(망고64)보드에 다운로드해줍니다. 
("안드로이드 시스템 프로그래밍 완전정복, 144페이지 참고) 


2. kernel 컴파일 
- .config 의 파일이 있으나 수정할필요는 없고 현재 설정이 최종입니다. 커널 빌드후 커널을 tftpboot폴더로 복사합니다.

kra@ubuntu:~/02.kernel$ make  kra@ubuntu:~/02.kernel$ cp arch/arm/boot/zImage  ~/tftpboot/zImage

 *. 컴파일 문제시 /home/kra/mango64_kernel/mango64_kernel_2010_07_02/ 폴더에서  make 수행해주세요.

1 # /etc/default/tftpd-hpa   2 TFTP_USERNAME="nobody"   3 TFTP_DIRECTORY="/home/kra/tftpboot"   4 TFTP_ADDRESS="0.0.0.0:69"   5 TFTP_OPTIONS="--secure"

- tftp 의 테스트는 아래의 스크립트와 같이 수행해줍니다. 

kra@ubuntu:~/tftpboot$ cat test.txt  Hello, This is a test file.  kra@ubuntu:~/tftpboot$ cd ..  kra@ubuntu:~$ tftp localhost  tftp> get test.txt  tftp> bye  ?Invalid command tftp> quit  kra@ubuntu:~$ cat test.txt  Hello, This is a test file.

*.  ("안드로이드 시스템 프로그래밍 완전정복, 113페이지, "7.2.1 TFTP - Ethernet Downloading server 설치" 참고) 

2.1 zImage 다운로드 

- "안드로이드 시스템 프로그래밍 완전정복, 157페이지, "11.3 Kernel 다운로드 후 NAND 저장 및 부팅"를 참고해주세요. 


3.root file system 컴파일 
- http://iggeak.tistory.com/15 을 참고로해서 루트파일 시스템을 만들어 줍니다. 
  /home/kra/nfsroot/RootFS-NEW2 폴더를 위주로 작업했습니다. 

 - 아래의 폴더에서 make 를 실행해줍니다.

kra@ubuntu:~/03.rootfs$ ll total 24 drwxr-xr-x 12 kra kra 4096 2011-09-27 20:05 bash-4.1 drwxr-xr-x 32 kra kra 4096 2012-03-24 11:58 busybox-1.17.0 -rwxr-xr-x 1 kra kra 110 2012-02-02 10:12 compile-rootfs.sh -rw-r--r-- 1 kra kra 1223 2010-07-24 15:40 Makefile drwxr-xr-x 8 kra kra 4096 2011-09-27 19:46 sysvinit-2.88dsf drwxr-xr-x 4 kra kra 4096 2010-07-24 15:40 target kra@ubuntu:~/03.rootfs$

3.1 nfs export 폴더 확인 
- cat /etc/exports 를 실행해봅니다. 
- 아래처럼 파일에서 /home/kra/nfsroot 폴더가 포함되어 있는지 확인합니다.

kra@ubuntu:~/03.rootfs$ cd .. kra@ubuntu:~$ cat /etc/exports # /etc/exports: the access control list for filesystems which may be exported # to NFS clients. See exports(5). # # Example for NFSv2 and NFSv3: # /srv/homes hostname1(rw,sync,no_subtree_check) hostname2(ro,sync,no_subtree_check) # # Example for NFSv4: # /srv/nfs4 gss/krb5i(rw,sync,fsid=0,crossmnt,no_subtree_check) # /srv/nfs4/homes gss/krb5i(rw,sync,no_subtree_check) # /home/kra/nfsroot *(rw,no_root_squash,no_all_squash,sync) /home/yhoh/nfsroot *(rw,no_root_squash,no_all_squash,sync) /nfsroot *(rw,no_root_squash,no_all_squash,sync) kra@ubuntu:~$

- MANGO64 프롬프트에서 환경변수를 확인합니다.
bootcmd=nand read 50008000  40000 300000; bootm 50008000
gatewayip=192.168.11.1
netmask=255.255.255.0
ipaddr=192.168.11.110
serverip=192.168.11.131
stdin=serial
stdout=serial
stderr=serial

- 아래와 같이 MANGO64 # 상태에서 환경변수를 바꿔줍니다. (nand 에서 부팅하도록 합니다.

MANGO64 # setenv bootargs "root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200" MANGO64 # print bootargs bootargs=root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200 MANGO64 #

 
3.2 스마트박스의 부트설정
- 아래와 같은 설정을 확인합니다.

bootcmd=nand read 50008000 40000 300000; bootm 50008000 bootargs_nand=root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200 bootargs_android_nfs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/m ango64_android,nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_ bd:eth0:off mem=128M init=/init console=ttySAC1,115200 bootargs_nfs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/RootFS-NE W2 ,nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0: off mem=128M console=ttySAC1,115200 bootargs=root=/dev/nfs rw nfsroot=192.168.11.131:/home/kra/nfsroot/RootFS-NEW2, nolock,tcp ip=192.168.11.110::192.168.11.1:255.255.255.0:mango64_bd:eth0:off mem =128M console=ttySAC1,115200 filesize=2FD9C4 fileaddr=51000000 gatewayip=192.168.11.1 netmask=255.255.255.0 ipaddr=192.168.11.110 serverip=192.168.11.131 stdin=serial stdout=serial stderr=serial

위 설정에서 bootargs_nand 는 bootargs 로 바꿔주면 nand 에서 부팅하게 설정이 바뀝니다.
또, bootargs_nfs를 bootargs 로 바꿔주면 nfs(network file system)을 통해서 부팅하도록 설정이 바뀝니다.

- 아래와 같이 환경변수를 바꿔줍니다. (nand에서 부팅하고 root filesystem은 yaffs2 라고 지정합니다.

MANGO64 # setenv bootargs="root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200"

3.3 루트파일 시스템 생성
아래와 같이 스크립트를 수행해줍니다.

kra@ubuntu:~/nfsroot$ cd /home/kra/nfsroot/ kra@ubuntu:~/nfsroot$ pwd /home/kra/nfsroot kra@ubuntu:~/nfsroot$ cat mk_smartbox-mango64.yaffs2.txt kra@ubuntu:~/nfsroot$ history | grep smartbox   671  sudo mkyaffs2image RootFS-NEW2 smartbox-mango64.yaffs2   673  sudo chmod 755 smartbox-mango64.yaffs2   680  cp smartbox-mango64.yaffs2  /home/kra/tftpboot/.   864  history | grep smartbox kra@ubuntu:~/nfsroot$ sudo mkyaffs2image RootFS-NEW2 smartbox-mango64.yaffs2 kra@ubuntu:~/nfsroot$ sudo chmod 755 smartbox-mango64.yaffs2 kra@ubuntu:~/nfsroot$ cp smartbox-mango64.yaffs2 /home/kra/tftpboot/. kra@ubuntu:~/nfsroot$

kra@ubuntu:~/nfsroot$ ll total 67656 drwxrwxrwx 2 kra kra 4096 2011-11-10 16:10 bkup -rwxrwxrwx 1 kra kra 1355216 2011-11-09 15:07 busybox -rwxrwxrwx 1 root root 149762 2011-12-11 16:31 libertas_sdio.ko drwxrwxrwx 19 root root 4096 2012-01-01 10:47 mango64_android -rwxrwxrwx 1 kra kra 293 2011-11-10 14:25 mk_smartbox-mango64.yaffs2.txt drwxrwxrwx 9 kra kra 4096 2011-10-29 01:45 nfs-temp drwxrwxrwx 18 kra kra 4096 2011-11-02 15:04 old.RootFS lrwxrwxrwx 1 kra kra 11 2012-01-06 20:08 RootFS -> RootFS-NEW2 drwxrwxrwx 17 root root 4096 2011-12-02 11:02 RootFS-NEW drwxrwxrwx 21 root root 4096 2011-12-31 12:08 RootFS-NEW2 lrwxrwxrwx 1 kra kra 34 2011-10-28 16:29 RootFS-NEW.tar -> /home/kra/Downloads/RootFS-NEW.tar drwxrwxrwx 5 kra kra 4096 2011-11-09 14:59 RootFS.old -rwxrwxrwx 1 kra kra 1361920 2011-11-09 17:08 rtc-busybox-1109.tar drwxrwxrwx 3 root root 4096 2011-11-11 19:58 sd -rwxrwxrwx 1 root root 66046464 2011-11-09 22:07 smartbox-mango64-1108.yaffs2 drwxrwxrwx 3 root root 4096 2011-10-24 19:59 tslib-arm -rwxrwxrwx 1 kra kra 317440 2011-12-30 23:51 tslib.tar kra@ubuntu:~/nfsroot$ cat mk_smartbox-mango64.yaffs2.txt kra@ubuntu:~/nfsroot$ history | grep smartbox 671 sudo mkyaffs2image RootFS-NEW2 smartbox-mango64.yaffs2 673 sudo chmod 755 smartbox-mango64.yaffs2 680 cp smartbox-mango64.yaffs2 /home/kra/tftpboot/. 864 history | grep smartbox kra@ubuntu:~/nfsroot$ pwd /home/kra/nfsroot

- 파일시스템 스마트박스에 다운로드 하기
- "안드로이드 시스템 프로그래밍 완전정복, 161페이지, "11.4 ... 및 루트파일시스템 생성"를 참고해주세요.

이부분은 다른 루트파일시스템 생성등을 참조하였고 smartbox에 yaffs2 이미지를 업로드하는 부분만 참고하였습니다. 따라서, 위에 언급한 책의 161페이지를 참조해주시기 바랍니다. smartbox-mango64.yaffs2 파일을 루트파일시스템으로 만들었고 /home/kra/nfsroot/RootFS-NEW2 디렉토리를 기본 디렉토리로 하였습니다. yaffs2파일 시스템은 아래와 같이 명령을 입력해주었습니다. kra@ubuntu:~/nfsroot$ sudo mkyaffs2image RootFS-NEW2 smartbox-mango64.yaffs2 또, 아래와 같이 속성변경 및 파일을 이동해주었습니다. kra@ubuntu:~/nfsroot$ sudo chmod 755 smartbox-mango64.yaffs2 kra@ubuntu:~/nfsroot$ cp smartbox-mango64.yaffs2 /home/kra/tftpboot/.

- 아래처럼 nand에 저장할 영역을 지워줍니다.

MANGO64 # nand erase 400000 8000000 NAND erase: device 0 offset 0x400000, size 0x8000000 Skipping bad block at 0x066e0000 Skipping bad block at 0x081e0000 Erasing at 0x83e0000 -- 100% complete. OK MANGO64 #

- 아래와 같이 tftp로 yaffs2 로 구성된 파일시스템을 다운로드합니다.

MANGO64 # tftp 51000000 smartbox-mango64.yaffs2 ......           #################################################################          #################################################################          ############### done Bytes transferred = 66046464 (0x3efca00) MANGO64 #

- 아래와 같이 nand에 write해줍니다.

MANGO64 # nand write.yaffs 51000000 400000 0x3efca00 NAND write: device 0 offset 0x400000, size 0x3efca00 Writing data at 0x4113800 -- 100% complete.  66046464 bytes written: OK MANGO64 #

- 이제 스마트박스를 부팅해줍니다. (저장이 안되는 경우가 있으므로 저장을 두번해주고 부팅해줍니다.)

MANGO64 # save Saving Environment to NAND... Erasing Nand... Erasing at 0x20000 -- 100% complete. Writing to Nand... done MANGO64 # save Saving Environment to NAND... Erasing Nand... Erasing at 0x20000 -- 100% complete. Writing to Nand... done MANGO64 # boot

- 아래와 같은 부팅로그가 출력됩니다.
U-Boot 1.3.4 (Sep 19 2011 - 01:21:21) for MANGO64 uboot-1.3.4-pooh11

 

 

CPU:     S3C6410@532MHz

         Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)

Board:   MANGO64

DRAM:    128 MB

Flash:   0 kB

NAND:    256 MB

In:      serial

Out:     serial

Err:     serial

Hit any key to stop autoboot:  3 2 1  3145728 bytes read: OK

Boot with zImage

 

Starting kernel ...

 

Uncompressing Linux............................................................................................................................................................................................................. done, booting the kernel.

Linux version 2.6.29 (kra@ubuntu) (gcc version 4.2.2) #70 Fri Jan 6 13:55:23 GMT 2012

CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f

CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache

Machine: MANGO6410

Ignoring unrecognised tag 0x41001099

Memory policy: ECC disabled, Data cache writeback

CPU S3C6410 (id 0x36410101)

S3C24XX Clocks, (c) 2004 Simtec Electronics

S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000

S3C64XX: HCLKx2=266000000, HCLK=133000000, PCLK=66500000

mout_apll: source is fout_apll (1), rate is 532000000

mout_epll: source is fout_epll (1), rate is 24000000

mout_mpll: source is mpll (1), rate is 532000000

mmc_bus: source is mout_epll (0), rate is 24000000

mmc_bus: source is mout_epll (0), rate is 24000000

mmc_bus: source is mout_epll (0), rate is 24000000

usb-bus-host: source is mout_epll (0), rate is 24000000

uclk1: source is dout_mpll (1), rate is 66500000

spi-bus: source is mout_epll (0), rate is 24000000

spi-bus: source is mout_epll (0), rate is 24000000

audio-bus: source is mout_epll (0), rate is 24000000

audio-bus: source is mout_epll (0), rate is 24000000

irda-bus: source is mout_epll (0), rate is 24000000

s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x50821000

s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x51221000

s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x51a21000

s3c64xx: 6291456 bytes SDRAM reserved for mfc at 0x52221000

s3c64xx: 4194304 bytes SDRAM reserved for jpeg at 0x52821000

s3c64xx: 1048576 bytes SDRAM reserved for cmm at 0x52c21000

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512

Kernel command line: root=/dev/mtdblock2 rootfstype=yaffs2 console=ttySAC1,115200

PID hash table entries: 512 (order: 9, 2048 bytes)

Console: colour dummy device 80x30

console [ttySAC1] enabled

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

allocated 655360 bytes of page_cgroup

please try cgroup_disable=memory option if you don't want

Memory: 128MB = 128MB total

Memory: 83968KB available (5680K code, 1027K data, 524K init)

SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)

Mount-cache hash table entries: 512

Initializing cgroup subsys debug

Initializing cgroup subsys ns

Initializing cgroup subsys cpuacct

Initializing cgroup subsys memory

Initializing cgroup subsys devices

Initializing cgroup subsys freezer

CPU: Testing write buffer coherency: ok

net_namespace: 564 bytes

NET: Registered protocol family 16

USB OTG Hardware Initializing

GPIO-150 autorequested

Camera Hardware Initializing

GPIO-165 autorequested

Wifi Hardware Initializing

GPIO-132 autorequested

GPIO-133 autorequested

Bluetooth Hardware Initializing(smartbox)

GPIO-130 autorequested

GPIO-131 autorequested

GPS Hardware Initializing

GPIO-135 autorequested

GPIO-134 autorequested

s3c64xx_dma_init: Registering DMA channels

s3c64xx_dma_init1: registering DMA 0 (c880c100)

s3c64xx_dma_init1: registering DMA 1 (c880c120)

s3c64xx_dma_init1: registering DMA 2 (c880c140)

s3c64xx_dma_init1: registering DMA 3 (c880c160)

s3c64xx_dma_init1: registering DMA 4 (c880c180)

s3c64xx_dma_init1: registering DMA 5 (c880c1a0)

s3c64xx_dma_init1: registering DMA 6 (c880c1c0)

s3c64xx_dma_init1: registering DMA 7 (c880c1e0)

PL080: IRQ 73, at c880c000

s3c64xx_dma_init1: registering DMA 8 (c8810100)

s3c64xx_dma_init1: registering DMA 9 (c8810120)

s3c64xx_dma_init1: registering DMA 10 (c8810140)

s3c64xx_dma_init1: registering DMA 11 (c8810160)

s3c64xx_dma_init1: registering DMA 12 (c8810180)

s3c64xx_dma_init1: registering DMA 13 (c88101a0)

s3c64xx_dma_init1: registering DMA 14 (c88101c0)

s3c64xx_dma_init1: registering DMA 15 (c88101e0)

PL080: IRQ 74, at c8810000

S3C6410: Initialising architecture

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Bluetooth: Core ver 2.15

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

cfg80211: Using static regulatory domain info

cfg80211: Regulatory domain: US

 (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

 (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)

 (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

 (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

 (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

 (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

 (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)

cfg80211: Calling CRDA for country: US

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 4, 81920 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

S3C64XX ADC driver, (c) 2008 Samsung Electronics

S3C64XX ADC driver successfully probed

audit: initializing netlink socket (disabled)

type=2000 audit(0.680:1): initialized

ashmem: initialized

NTFS driver 2.1.29 [Flags: R/W DEBUG].

JFFS2 version 2.2. (NAND) 짤 2001-2006 Red Hat, Inc.

yaffs Dec  5 2011 01:06:05 Installing.

msgmni has been set to 164

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

GPIO-153 autorequested

GPIO-53 autorequested

S3C_LCD clock got enabled :: 133.000 Mhz

LCD TYPE :: LTE480WV will be initialized

Window[0] - FB1: map_video_memory: clear ff000000:00177000

            FB1: map_video_memory: dma=57c00000 cpu=ff000000 size=00177000

Window[0] - FB2: map_video_memory: clear ff0bb800:000bb800

            FB2: map_video_memory: dma=57cbb800 cpu=ff0bb800 size=000bb800

Console: switching to colour frame buffer device 100x30

fb0: s3cfb frame buffer device

s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10

s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10

s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10

s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10

brd: module loaded

loop: module loaded

PPP generic driver version 2.4.2

smsc911x: Driver version 2008-10-21.

smsc911x-mdio: probed

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)

net eth0: MAC Address: ea:a3:4f:d9:3e:6a

libertas_sdio: Libertas SDIO driver

libertas_sdio: Copyright Pierre Ossman

8686 sdio: sd 8686 driver:[Dec 12 2011,15:37:18]

8686 sdio: Copyright HHCN 2009

console [netcon0] enabled

netconsole: network logging started

Linux video capture interface: v2.00

s3c-fimc: controller 0 registered successfully

s3c-fimc: controller 1 registered successfully

S3C6400 MFC Driver, (c) 2007 Samsung Electronics

S3C6400 MFC Driver, (c) 2007 Samsung Electronics

S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics

S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics

 S3C6410 TV encoder Driver init OK.

S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics

 S3C6410 TV scaler Driver init OK.

S3C Rotator Driver, (c) 2008 Samsung Electronics

s3c_rotator_probe called

s3c_rotator_probe success

S3C JPEG Driver, (c) 2007 Samsung Electronics

s3c_g2d_probe called

 s3c_g2d_probe Success

 S3C G2D Init : Done

S3C G3D Driver, (c) 2007-2009 Samsung Electronics

s3c_g3d version : 0x1050000

 S3C G3D Init : Done

S3C CMM Driver, (c) 2008 Samsung Electronics

Driver 'sd' needs updating - please use bus_type methods

S3C NAND Driver, (c) 2008 Samsung Electronics

S3C NAND Driver is using hardware ECC.

NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)

Creating 4 MTD partitions on "NAND 256MiB 3,3V 8-bit":

0x000000000000-0x000000040000 : "Bootloader"

0x000000040000-0x000000400000 : "Kernel"

0x000000400000-0x00000a800000 : "Rootfs"

0x00000a800000-0x000010000000 : "File System"

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics

s3c-udc : version 15 March 2009 (DMA Mode)

android adb driver

Registered gadget driver 'android_adb'

mice: PS/2 mouse device common for all mice

input: mango64-keypad as /devices/virtual/input/input0

Mango64 dev board keypad driver initialized!!

S3C Touchscreen driver, (c) 2008 Samsung Electronics

S3C TouchScreen got loaded successfully : 12 bits

input: S3C TouchScreen as /devices/virtual/input/input1

S3C24XX RTC, (c) 2004,2006 Simtec Electronics

s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling

s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0

i2c /dev entries driver

s3c2440-i2c s3c2440-i2c.0: slave address 0x10

s3c2440-i2c s3c2440-i2c.0: bus frequency set to 377 KHz

parent clock for camera: 266.000 MHz, divisor: 9

s3c2440-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter

s3c2440-i2c s3c2440-i2c.1: slave address 0x10

s3c2440-i2c s3c2440-i2c.1: bus frequency set to 377 KHz

parent clock for camera: 266.000 MHz, divisor: 9

s3c2440-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter

S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics

s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled

Bluetooth: Virtual HCI driver ver 1.2

Bluetooth: HCI UART driver ver 2.2

Bluetooth: HCI H4 protocol initialized

Bluetooth: HCI BCSP protocol initialized

Bluetooth: HCILL protocol initialized

sdhci: Secure Digital Host Controller Interface driver

sdhci: Copyright(c) Pierre Ossman

s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)

s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)

s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)

mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA

s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)

s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)

s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)

mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA

usbcore: registered new interface driver usbhid

usbhid: v2.6:USB HID core driver

logger: created 64K log 'log_main'

logger: created 256K log 'log_events'

logger: created 64K log 'log_radio'

gps power driver

smb380 driver init

Advanced Linux Sound Architecture Driver Version 1.0.18a.

WM8960 I2C Codec 0-001a: No platform data supplied

mmc0: new SDIO card at address 0001

libertas_sdio mmc0:0001:1: firmware: using built-in firmware sd8686_helper.bin

libertas_sdio mmc0:0001:1: firmware: using built-in firmware sd8686.bin

libertas: 00:50:43:02:fe:01, fw 9.70.3p24, cap 0x0000030b

eth1 (libertas_sdio): not using net_device_ops yet

libertas: PREP_CMD: command 0x00a3 failed: 2

libertas: PREP_CMD: command 0x00a3 failed: 2

libertas: eth1: Marvell WLAN 802.11 adapter

532----WM8960_ADDCTL2: 0x0

mmc1: new high speed SDHC card at address 0001

mmcblk0: mmc1:0001 00000 7.60 GiB

 mmcblk0:<7>mmc1: starting CMD18 arg 00000000 flags 000000b5

532----WM8960_ADDCTL2: 0x60

532----WM8960_ADDCTL3: 0x0

 p1

532----WM8960_ADDCTL3: 0x8

532----WM8960_IFACE2: 0x0

532----WM8960_IFACE2: 0x40

532----WM8960_LOUT1: 0x100

532----WM8960_LOUT1: 0x17F

532----WM8960_ROUT1: 0x100

532----WM8960_ROUT1: 0x17F

WM8960_LOUT2: 0x17F

WM8960_ROUT2: 0x17F

WM8960_POWER2: 0xFF

WM8960_CLASSD1: 0xF7

WM8960_CLASSD3: 0xAD

before snd_soc_register_codec()

----WM8960_RINVOL  (0x1): 0x197

----WM8960_LOUT1   (0x2): 0x17F

----WM8960_ROUT1   (0x3): 0x17F

----WM8960_CLOCK1  (0x4): 0x0

----WM8960_DACCTL1 (0x5): 0x8

----WM8960_DACCTL2 (0x6): 0x0

----WM8960_IFACE1  (0x7): 0xA

----WM8960_CLOCK2  (0x8): 0x1C0

----WM8960_IFACE2  (0x9): 0x40

----WM8960_LDAC    (0xA): 0x1FF

----WM8960_RDAC    (0xB): 0x1FF

----WM8960_RESET   (0xF): 0x0

----WM8960_3D      (0x10): 0x0

----WM8960_ALC1    (0x11): 0x7B

----WM8960_ALC2    (0x12): 0x100

----WM8960_ALC3    (0x13): 0x32

----WM8960_NOISEG  (0x14): 0x0

----WM8960_LADC    (0x15): 0x1C3

----WM8960_RADC    (0x16): 0x1C3

----WM8960_ADDCTL1 (0x17): 0x1C0

----WM8960_ADDCTL2 (0x18): 0x60

----WM8960_POWER1  (0x19): 0x140

----WM8960_POWER2  (0x1A): 0xFF

----WM8960_ADDCTL3 (0x1B): 0x8

----WM8960_APOP1   (0x1C): 0x8

----WM8960_APOP2   (0x1D): 0x0

----WM8960_LINPATH (0x20): 0x100

----WM8960_RINPATH (0x21): 0x100

----WM8960_LOUTMIX (0x22): 0x50

----WM8960_ROUTMIX (0x25): 0x50

----WM8960_MONOMIX1(0x26): 0x0

----WM8960_MONOMIX2(0x27): 0x0

----WM8960_LOUT2   (0x28): 0x17F

----WM8960_ROUT2   (0x29): 0x17F

----WM8960_MONO    (0x2A): 0x40

----WM8960_INBMIX1 (0x2B): 0x0

----WM8960_INBMIX2 (0x2C): 0x0

----WM8960_BYPASS1 (0x2D): 0x50

----WM8960_BYPASS2 (0x2E): 0x50

----WM8960_POWER3  (0x2F): 0x0

----WM8960_ADDCTL4 (0x30): 0x2

----WM8960_CLASSD1 (0x31): 0xF7

----WM8960_CLASSD3 (0x33): 0xAD

----WM8960_PLL1    (0x34): 0x8

----WM8960_PLL2    (0x35): 0x31

----WM8960_PLL3    (0x36): 0x26

----WM8960_PLL4    (0x37): 0xE9

No device for DAI s3c64xx-i2s

soc-audio soc-audio.0: RXEN: Invalid MODE in IISMOD

WM8960 Audio Codec TEST

asoc: WM8960 <-> s3c64xx-i2s mapping ok

 WM8960_probe() : LOUT2, ROUT2, setting 0x07f

ALSA device list:

  #0: smdk6410 (WM8960)

oprofile: using arm/armv6

TCP cubic registered

NET: Registered protocol family 17

NET: Registered protocol family 15

Bluetooth: L2CAP ver 2.13

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO (Voice Link) ver 0.6

Bluetooth: SCO socket layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM TTY layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

lib80211: common routines for IEEE802.11 drivers

VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5

s3c2410-rtc s3c2410-rtc: setting system clock to 2012-03-26 19:55:40 UTC (1332791740)

yaffs: dev is 32505858 name is "mtdblock2"

yaffs: passed flags ""

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

yaffs: restored from checkpoint

yaffs_read_super: isCheckpointed 1

VFS: Mounted root (yaffs2 filesystem) on device 31:2.

Freeing init memory: 524K

INIT: version 2.88 booting

 

    System initialization...

 

    Hostname       : MANGO64_S

    Filesystem     : v1.0.0

 

 

    Kernel release : Linux 2.6.29

    Kernel version : #70 Fri Jan 6 13:55:23 GMT 2012

 

 Mounting /proc             : [SUCCESS]

 Mounting /sys              : [SUCCESS]

 Mounting /dev              : [SUCCESS]

 Mounting /dev/pts          : [SUCCESS]

 Enabling hot-plug          : [SUCCESS]

 Populating /dev            : [SUCCESS]

 Mounting other filesystems : [SUCCESS]

 Starting telnetd           :

System initialization complete.

GPL(13)=1

m64led_init(), 0x64 -> 1

INIT - ADCCON

 

m64led device initialized.

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

INIT: Entering runlevel: 3

 

 

MANGO64_S login: root

login[1134]: root login on 'console'

root@MANGO64_S:~#

root@MANGO64_S:~#

root@MANGO64_S:~#

root@MANGO64_S:~#

root@MANGO64_S:~# pwd

/root

root@MANGO64_S:~# mout nt

rootfs on / type rootfs (rw)

/dev/root on / type yaffs2 (rw)

/proc on /proc type proc (rw)

sysfs on /sys type sysfs (rw)

mdev on /dev type tmpfs (rw)

devpts on /dev/pts type devpts (rw,mode=600,ptmxmode=000)

/dev/mmcblk0p1 on /mnt/sdmemory type ext2 (rw,errors=continue)

root@MANGO64_S:~#

- /etc/profile 파일의 내용은 아래와 같습니다.

root@MANGO64_S:/etc# cat profile # /etc/profile: system-wide .profile file for the Bourne shell (sh(1)) # and Bourne compatible shells (bash(1), ksh(1), ash(1), ...).   PATH="/usr/local/bin:/usr/bin:/bin" EDITOR="/bin/vi"            # needed for packages like cron   export DISPLAY=:0   test -z "$TERM" && TERM="vt100" # Basic terminal capab. For screen etc.   if [ ! -e /etc/localtime ]; then     TZ="UTC"        # Time Zone. Look at http://theory.uwinnipeg.ca/gnu/glibc/libc_303.html                 # for an explanation of how to set this to your local timezone.     export TZ fi   if [ "`id -u`" -eq 0 ]; then    PATH=$PATH:/usr/local/sbin:/usr/sbin:/sbin: fi if [ "$PS1" ]; then # works for bash and ash (no other shells known to be in use here)    PS1='\u@\h:\w\$ ' fi   if [ -d /etc/profile.d ]; then   for i in /etc/profile.d/*.sh; do     if [ -r $i ]; then       . $i     fi   done   unset i fi   #PATH=/usr/local/Trolltech/QtopiaCore-4.3.5/bin:$PATH PATH=/usr/local/qt/bin:$PATH export PATH PS1 OPIEDIR QPEDIR QTDIR EDITOR TERM   #QWS_DISPLAY="LinuxFb:mmWidth106:mmHeight66:0" QWS_DISPLAY="LinuxFb:mmWidth136:mmHeight96:0" export QWS_DISPLAY   export QWS_MOUSE_PROTO=tslib:/dev/input/event1     umask 022   # tslib option export TSDIR=/usr/local/tslib export LD_LIBRARY_PATH=$TSDIR/lib:$LD_LIBRARY_PATH export TSLIB_TSDEVICE=/dev/input/event1 export TSLIB_CONFFILE=$TSDIR/etc/ts.conf export TSLIB_CALIBFILE=/etc/pointercal   export env TZ=GMT-09:00:00   root@MANGO64_S:/etc#

/etc/rc.d/rc.sysinit 파일내용은 아래와 같습니다.
> 아래에서 mount -t vfat ... 부분이 있는데 "-t vfat " 부분을 제거해줍니다. 그러면 SD memory가 마운트 됩니다.
초기 sd memory 를 fat 방식으로 해서 생긴 문제입니다.

root@MANGO64_S:/etc/rc.d# cat rc.sysinit #!/bin/sh #   --------------------------------------------- #   Common settings #   --------------------------------------------- HOSTNAME=MANGO64_S VERSION=1.0.0   hostname $HOSTNAME   #   --------------------------------------------- #   Prints execution status. # #   arg1 : Execution status #   arg2 : Continue (0) or Abort (1) on error #   --------------------------------------------- status () {     if [ $1 -eq 0 ] ; then         echo "[SUCCESS]"     else         echo "[FAILED]"               if [ $2 -eq 1 ] ; then                 echo "... System init aborted."                     exit 1             fi     fi }   #   --------------------------------------------- #   Get verbose #   --------------------------------------------- echo "" echo "    System initialization..." echo "" echo "    Hostname       : $HOSTNAME" echo "    Filesystem     : v$VERSION" echo "" echo "" echo "    Kernel release : `uname -s` `uname -r`" echo "    Kernel version : `uname -v`" echo ""     #   --------------------------------------------- #   MDEV Support #   (Requires sysfs support in the kernel) #   --------------------------------------------- echo -n " Mounting /proc             : " mount -n -t proc /proc /proc status $? 1   echo -n " Mounting /sys              : " mount -n -t sysfs sysfs /sys status $? 1   echo -n " Mounting /dev              : " mount -n -t tmpfs mdev /dev status $? 1   echo -n " Mounting /dev/pts          : " mkdir /dev/pts mount -t devpts devpts /dev/pts status $? 1   echo -n " Enabling hot-plug          : " echo "/sbin/mdev" > /proc/sys/kernel/hotplug status $? 0   echo -n " Populating /dev            : " mkdir /dev/input mkdir /dev/snd   mdev -s status $? 0   #   --------------------------------------------- #   Mount the default file systems #   --------------------------------------------- echo -n " Mounting other filesystems : " mount -a status $? 0     #   --------------------------------------------- #   Set PATH #   --------------------------------------------- export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin   echo -n " Starting telnetd           : " /usr/sbin/telnetd   #   --------------------------------------------- #   Done! #   --------------------------------------------- echo "" echo "System initialization complete."   # custom device initialization mknod /dev/input/event0 c 13 64 mknod /dev/input/event1 c 13 65   mknod  /dev/m64led c 248 249 insmod /qt-demos/m64led.ko echo "" echo "m64led device initialized." #mount -t vfat /dev/mmcblk0p1  /mnt/sdmemory/ mount  /dev/mmcblk0p1  /mnt/sdmemory/ echo "sd memory is mounted as /mnt/sdmemory"   root@MANGO64_S:/etc/rc.d#

 

- /root/.profile 파일을 수정해줍니다. (명령어 입력모드에서 ll 이나 h 만 입력해도 되게 됩니다.

root@MANGO64_S:~# cat .profile alias ll='ls -al' alias h='history' root@MANGO64_S:~#

 

4. 터치스크린 컴파일 
 - 아래의 폴더에서 make 를 실행해줍니다.

kra@ubuntu:~$ cd 04.tslib kra@ubuntu:~/04.tslib$ ls kra@ubuntu:~/04.tslib$ cat compile-tslib.sh #git clone http://github.com/kergoth/tslib.git #How to get tslib source   #svn co svn://svn.berlios.de/tslib/trunk/tslib    tslib   # 1.---     ./autogen.sh     # compile for arm cpu  ./configure --host=arm-none-linux-gnueabi --prefix=/usr/local/tslib --enable-static --enable-shared --disable-h3600 --disable-corgi --disable-collie run sudo chmod -R 777 /usr/local/tslib make  make install

*. 타겟보드에서 바이너리를 복사해서 ts_calibrate 를 실행해줍니다. 


5. qt4.7 컴파일 방법 
 - 아래의 폴더에서 make 를 실행해줍니다., tslib 는 /usr/local/tslib 에 있는 파일을 사용합니다. 

kra@ubuntu:~/05.qt4.7$ cat qt4.7-compile.sh   # -prefix usr/local/qt    is added for compile destination folder ./configure  -prefix /opt/qt4.7  -opensource  -embedded arm -xplatform qws/linux-arm-g++   -little-endian -release  -no-largefile -no-accessibility -no-qt3support -no-webkit -qt-zlib -qt-gif -qt-libpng  -no-libmng -qt-libjpeg -no-nis -no-cups -qt-freetype -depths 24 -L -qt-mouse-tslib

   
6. sound 컴파일 방법 
 - 아래의 폴더에서 make 를 실행해줍니다. 아래 파일을 참고해서 컴파일 합니다. 

kra@ubuntu:~/06.sound$ cat  alsa-compile.txt

7. device test  컴파일 방법 
 - 아래 파일을 참고해서 컴파일 합니다.

kra@ubuntu:~$ cd 07.mango64-test/  kra@ubuntu:~/07.mango64-test$ cat   ./compile_led-test.sh echo "arm-none-linux-gnueabi-gcc  led-test.c  -o led-test" arm-none-linux-gnueabi-gcc  led-test.c  -o led-test  echo "copy led-test to ~/nfsRoot/RootFS-NEW/qt-demos/ is required" sudo cp led-test ~/nfsroot/RootFS-NEW2/qt-demos/. kra@ubuntu:~/07.mango64-test$

http://knightjbs.springnote.com/pages/5078547

http://iggeak.tistory.com/category/QT
 위 링크가 원본글입니다.